寧鄉力士樂伺服驅動器維修保養：
D900:D9 Command Automatic Loop Control
命令自動回路控制
Description:說明：
The start of this command means that an automatic control loop setting is
executed in the drive if the drive is in the loop at command start, i.e., the
drive enable signal is applied.此命令的啟動意味著自動控制回路設置如果驅動器在命令啟動時處于循環中，則在驅動器中執行，即施加驅動使能信號。
力士樂伺服驅動器主板故障維修:
⇒ The start of this command can trigger a movement if drive enable and drive start are at the drive.
如果驅動器啟用和驅動器啟動在驅動器上，則此命令的啟動可以觸發移動。
⇒ The drive conducts autonomous movements within the range defined by both limits.驅動器在兩個極限限定的范圍內進行自主運動。
⇒ The E-stop sequence function and the travel range limit switch must be guaranteed and checked.
必須保證并檢查緊急停止順序功能和行程范圍限制開關。
See also Function description:"Safety Instructions"
另請參閱功能說明：“安全說明”
⇒ During command D9, the drive autonomously conducts motions, i.e., without external command value.
在指令D9期間，驅動器自主地進行運動，即沒有外部指令值。
Note: Under some circumstances, errors can also occur while the command is being executed.
在某些情況下，在執行命令時也可能發生錯誤。
These are then signalled with pertinent messages..
然后用相關信息向這些信號發送信號。
D901 start only with RF
僅從RF開始
D902 motor feedback not valid
電機反饋無效
D903 inertia detection failed
慣性檢測失敗
D904 gain adjustment failed
增益調整失敗
D905 wrong position range
錯誤的位置范圍
D906 position range exceeded
超出位置范圍
轉載請注明出處：上海仰光電子科技專業伺服驅動器維修,伺服電機維修
本文鏈接：http://taghkj.com/fuwu/Services_Show23348.htm
伺服驅動器維修 伺服電機維修 觸摸屏維修 變頻器維修
電話：021-50157782
手機：13817011982 微信同號
郵箱：shygdzi@163.com
聯系人：張工
網址：http://taghkj.com
【 我們確保修好測試好給客戶！！！！】
下一篇：沒有了
